Choose language

EnglishEspañolDeutsch日本語한국어Tiếng ViệtไทยFrançaisItalianoPortuguêsРусский简体中文
Home > Industry news > How to choose T23-S200, S255, S351 arc guide rail? Center diameter versus layout options

How to choose T23-S200, S255, S351 arc guide rail? Center diameter versus layout options

Technical Popularization · 2026-11-11 · Weisepu Technology Department
How to choose T23-S200, S255, S351 arc guide rail? Center diameter versus layout options
The main difference between T23-S200, S255 and S351 is the arc center diameter. When selecting the model, you should first check the equipment turning space and fixture envelope, and then confirm it based on the load, cycle time and straight section splicing method.

T23-S200, T23-S255, and T23-S351 are all T23 series arc guide rails. Which model to choose, first check how much space can be left in the turning position of the equipment, and then check whether the carriages and fixture will interfere when cornering.

ModelArc center diameterRegular arc angleInitial applicable ideas
T23-S200200mm90° / 180° / 360°Prioritize kernel map when turning space is tight
T23-S255255mm90° / 180° / 360°Want to strike a balance between compactness and fixture margin
T23-S351351mm90° / 180° / 360°The turning area is wider, requiring more space for fixtures and maintenance

All three models are available in GCr15 or 440C material, with a surface hardness of HRC58~62, and can also be spliced with T23 straight guide rails.

Don’t just look at “diameter”

The numbers S200, S255, and S351 represent the arc center diameter, not the footprint of the entire equipment, nor can they be directly understood as the increasing load capacity from small to large.

During the actual layout, the guide rail outline, carriages, tooling, workpieces, guards, cables and maintenance positions must also be put into the drawing for verification. Especially when the jig has a large overhang, the workpiece is eccentric, or frequent starts and stops are required, whether the arc segment can operate stably must be judged based on the complete working conditions.

How to make the initial choice?

When space is tight on site, look to the S200 first.

But you cannot just draw a circle based on 200mm. You need to check the maximum sweeping range of the fixture when turning.

When the S200 corners too tight, compare to the S255.

It is suitable for those who need to add a little more turning margin, but do not want the overall line size to become significantly larger.

When the tooling is larger or there is more space for maintenance, S351 can be compared.

The center diameter is larger, and it is usually easier to arrange fixtures and guards; whether to use it still depends on the length of the straight section, the number of work stations, the load and the cycle time.

It is recommended to prepare these information before selection

• Equipment layout drawings or site dimensions;

• Arc position and desired turning direction;

• Number of slides and center distance between workstations;

• Maximum outline of the fixture and workpiece;

• Total load of single slide;

• Tempo, speed and positioning requirements;

• Whether it needs to be spliced with T23 straight section rail.

If the standard S200, S255, and S351 are not suitable for the on-site route, non-standard solutions can be confirmed based on the actual radius, angle, number of slides, and center distance. The final result shall be the STEP model and the 2D/3D drawings confirmed by both parties.

Related products

•T23-S200 arc guide rail product parameters and STEP drawing download

• T23-S255 arc guide rail product parameters and STEP drawing download

• T23-S351 arc guide rail product parameters and STEP drawing download

Need help with selection or technical advice?
Ring guide rails/arc guide rails/V-shaped guide rails and complete line solutions support non-standard customization.
Call +86 18912659251
Have a specific project to evaluate? Send us the production line rhythm and workpiece parameters, and we will provide you with a practical technical solution.
Get in touch
苏州威赛普精密机械有限公司 版权所有  | Su ICP No. 2021007187-2
Inquiry