Choose language

EnglishEspañolDeutsch日本語한국어Tiếng ViệtไทยFrançaisItalianoPortuguêsРусский简体中文
Home > Industry news > Circular guide rail selection: How to calculate load, cycle time and speed together?

Circular guide rail selection: How to calculate load, cycle time and speed together?

Technical Popularization · 2026-11-12 · Weisepu Technology Department
Circular guide rail selection: How to calculate load, cycle time and speed together?
The model and driving mode of the circular guide rail need to be judged together with the total load of the single slide, the number of work stations, the cycle time, the operating mode and the positioning requirements. Only looking at one of the parameters can easily lead to a small solution or redundant configuration.

When selecting a ring guide rail, you can't just ask "how many kilograms it can carry" or "how fast it can run". The load, number of slides, work station spacing, cycle time, operation mode and positioning accuracy of an actual production line are related to each other. Only by putting these conditions together can we judge whether the guide rail specifications and driving method are suitable.

The load of a single slide must be calculated as the entire following weight.

When making an inquiry, you cannot only provide the weight of the workpiece. The total load of a single slide usually includes:

Workpiece + jig + fixture + mounting plate + sensors, cylinders and other follow-up parts

If the center of gravity of the workpiece or fixture is biased to one side, the unbalanced load situation should also be explained. When the center of gravity is high, the overhang is long, or the vehicle starts and stops frequently, the actual dynamic requirements will be higher than the static placement state.

Therefore, "workpiece 1kg" is not equal to "single slide load 1kg", and the selection should be based on the total mass of all following parts on the slide.

The cycle time is not equal to the rail speed

The cycle time is the time required to complete a station advancement, stay or cycle; the speed is the movement speed of the slide on the track, and the two cannot be confused.

For example, a certain station completes assembly every 30 seconds, which may be continuous operation, or it may move one station and then stop processing. When confirming needs, it is recommended to explain:

  • Does the guide rail run continuously, stop and go for indexing or reciprocate?
  • Residence time at a single workstation;
  • distance moved each time;
  • Whether it needs to be positioned in place;
  • Whether there are frequent starts and stops.

The number of slides and center distance determine how the workstations are arranged.

The greater the number of slides, the higher the production capacity is. It also depends on the operating space required for each workstation and whether there will be interference between the fixtures.

The preliminary layout can first confirm three questions:

  • Several workstations are required;
  • What is the required center distance between adjacent work stations;
  • Whether additional space is required for tooling, inspection, loading and unloading, and maintenance.

If the center distance is too small, the fixtures may interfere with each other; if the center distance is too large, the entire line size and cost will increase. The number of workstations, center distance and wire body size need to be determined together.

Acceleration, deceleration and cornering increase dynamic requirements

Frequent starts and stops, small-radius turns, eccentric loading of fixtures or a high center of gravity will increase the dynamic requirements during operation. It is recommended that the following situations be clearly stated during the planning stage:

  • Frequent starts and stops or short-term acceleration and deceleration;
  • The center of gravity of the fixture is high and the eccentric load is obvious;
  • There is impact, vibration or liquid sloshing in the workpiece;
  • There are requirements for repeated positioning accuracy;
  • The arc radius is small and the turning space is compact.

These factors will affect the guide rail, slide, drive, motor, reducer and positioning scheme, and cannot be judged based on static load alone.

The driving method should be confirmed according to the working conditions.

The chain type is usually suitable for scenarios that require stable circulation, large loads, or many workstations; the synchronous belt type runs more smoothly and is suitable for projects with light loads, low noise, or high cleanliness requirements. Cam linkage and magnetic levitation are suitable for scenes with clear motion patterns or special process requirements.

The specific driving method to be used must be confirmed based on the load, speed, cycle time, positioning accuracy and maintenance requirements.

You need to first understand the overall selection logic of ring guide rails, you can read"How to choose a circular guide rail? Load, turning radius and repeat positioning accuracy》。

Also read further:How to choose the circular guide rail driving method? Comparison of four drivers

Before making an inquiry, it is recommended to prepare these information

  • The total load of a single slide and the outline of the fixture;
  • Number of slides, center distance and number of workstations;
  • Operation mode: continuous, stop-and-go indexing or reciprocating;
  • Single station cycle time, whole line cycle time and positioning requirements;
  • Speed, start and stop frequency and whether there is impact load;
  • Line layout size, arc radius and installation method;
  • Site environment, such as dust, moisture, corrosion or cleanliness requirements;
  • CAD drawings, layout drawings or site photos.

Not sure how to get started? You can use the online selection system first

If you do not have complete CAD drawings yet, you can first go throughWeisepu Ring Guide Automatic Selection SystemOrganize basic requirements such as guide rail type, line shape, number of work stations, load, cycle time and on-site space.

The system results can be used as a reference for early program communication; when it comes to actual load bearing, operating speed, positioning accuracy, non-standard radius and installation details, technical confirmation still needs to be carried out based on drawings and complete working conditions.

In the customized line case disclosed on the official website, a configuration of 30 carriages, a single carriages of 1kg, and a 30-second cutting step was used. This is just the working condition of this project and does not represent the universal load and speed standards for all ring guide or arc guide components.

Conclusion:The key to ring guide rail selection is not to pursue higher load or faster speed alone, but to match the load, cycle time, number of slides, layout and driving method. When you have preliminary needs, you can enterWeisepu Ring Guide Automatic Selection System, first obtain the product direction and solution communication portal.



Need help with selection or technical advice?
Ring guide rails/arc guide rails/V-shaped guide rails and complete line solutions support non-standard customization.
Call +86 18912659251
Have a specific project to evaluate? Send us the production line rhythm and workpiece parameters, and we will provide you with a practical technical solution.
Get in touch
苏州威赛普精密机械有限公司 版权所有  | Su ICP No. 2021007187-2
Inquiry